Effects of Sintering Temperature on Microstructure and Properties of Ag-25.5Cu-27Sn Brazing Filler Metal by Magnetic Pulse Compaction

ZHU Chaoyong; HUANG Shangyu; ZHOU Mengcheng; YAN Shiwei; LEI Yu

doi:10.11973/jxgccl201712016

Materials and Mechanical Engineering > 2017 > 41(12): 75-79. > DOI: 10.11973/jxgccl201712016

ZHU Chaoyong, HUANG Shangyu, ZHOU Mengcheng, YAN Shiwei, LEI Yu. Effects of Sintering Temperature on Microstructure and Properties of Ag-25.5Cu-27Sn Brazing Filler Metal by Magnetic Pulse Compaction[J]. Materials and Mechanical Engineering, 2017, 41(12): 75-79. DOI: 10.11973/jxgccl201712016

Citation:

PDF (11963 KB)

Effects of Sintering Temperature on Microstructure and Properties of Ag-25.5Cu-27Sn Brazing Filler Metal by Magnetic Pulse Compaction

1. School of Materials Science and Engineering, Wuhan University of Technology, Wuhan 430070, China;
2. State Key Laboratory of Material Processing and Die & Mould Technology, Huazhong University of Science and Technology, Wuhan 430074, China

More Information

Received Date: December 12, 2016
Revised Date: September 19, 2017

Graphical Abstract

Abstract

Abstract

Ag-25.5Cu-27Sn brazing filler metal was prepared by magnetic pulse compaction using pure metal powders as raw materials, and sintered at 100-500℃ for 30 min. The effects of sintering temperature on relative density, phase composition, microstructure, melting property of the brazing filler metal, and on the micromorphology and tensile strength of the brazed Cu joint were studied. The results show that the relative density of the brazing filler metal first decreased then increased with the increase of sintering temperature. The relative density of the brazing filler metal sintered at 400℃ was higher than that of the unsintered brazing filler metal, and the stable phases of ε₁-Cu₃Sn and ε₂-Ag₃Sn were formed. The melting temperature of the brazing filler metal was improved by sintering, and that of the brazing filler metal sintered at 400℃ was about 4℃ lower than that sintered at 250℃. With 400℃ sintered brazing filler metal, the number of pores in weld of the brazed Cu joint was relatively small and the microstructure was relatively homogeneity and fine. The tensile strength was 16% higher than that of Cu joint brazed with the unsintered filler metal.
- magnetic pulse compaction,
- Ag-Cu-Sn brazing filler metal,
- sinter,
- phase composition

FullText(HTML)

References (15)

References

[1]	张启运,庄鸿寿. 钎焊手册[M]. 2版. 北京:机械工业出版社, 2008.
[2]	陈登权,李伟,罗锡明,等. 电子工业用金基和银基中温钎料的研究进展[J]. 贵金属,2009(3):62-67.
[3]	甘卫平,陈慧,杨伏良. Ag-Cu-In-Sn钎料加工工艺的研究[J]. 材料导报,2007(3):156-158.
[4]	MA X, LI L, ZHANG Z, et al. Effects of rare earth La on microstructure and properties of Ag-21Cu-25Sn alloy ribbon prepared by melt spinning[J]. Materials & Design, 2015, 83:1-5.
[5]	徐锦锋,张晓存, 翟秋亚,等. 镍对Ag-Cu-Sn-In钎料组织及加工性能的影响[J]. 焊接学报, 2011, 32(11):65-68.
[6]	李良锋,丘泰,李晓云,等. 机械合金化法制备57.6Ag-22.4Cu-10.5In-9.5Sn合金粉末及其性能[J]. 机械工程材料,2008,32(8):30-32.
[7]	史耀武,雷永平, 夏志东,等. 无铅焊膏的设计与展望[J]. 电子元件与材料, 2008, 27(9):31-34.
[8]	黄尚宇,施健, 孟正华,等. PZT陶瓷粉末低电压电磁压制实验研究[J]. 塑性工程学报, 2007, 8(1):42-47.
[9]	ZHOLNIN A, KOVALEVA I, MEDVEDEV P, et al. Difference of magnetic pulse compaction from traditional uniaxial pressing of alumina nanopowders[J]. Physics Procedia, 2015, 72:382-385.
[10]	徐志坤. 无镉中温银基钎料的低电压电磁压制及烧结工艺研究[D].武汉:武汉理工大学,2012.
[11]	张志力,熊惟皓,张国鹏.烧结温度对(Ti,W,Mo)C-Ni金属陶瓷组织与性能的影响[J].机械工程材料,2013,37(12):46-49.
[12]	蔺绍江,熊惟皓,姚振华,等. 烧结温度对316不锈钢粉末冶金烧结体组织和性能的影响[J]. 机械工程材料,2011, 35(1):22-25.
[13]	汤文明, IVEY G D. 电沉积Ag/Sn偶界面反应及其动力学[J]. 中国有色金属学报, 2009, 19(5):930-935.
[14]	宋玉强, 李世春. Cu粉和Sn粉相界面扩散溶解层的研究[J]. 稀有金属材料与工程, 2007, 36(增刊3):217-221.
[15]	YEN Y, CHEN S. Phase equilibria of the Ag-Sn-Cu ternary system[J]. Journal of Materials Research, 2004, 19(8):2298-2305.

Cited By

Get Citation

PDF

XML

Article views (1) PDF downloads (0)

Turn off MathJax

Article Contents

Abstract

References

Effects of Sintering Temperature on Microstructure and Properties of Ag-25.5Cu-27Sn Brazing Filler Metal by Magnetic Pulse Compaction

Abstract

References

Catalog

Export File

Citation

Format

Content