A New 700 MPa Low Carbon High Strength Steel

YI Hai-long; DU Lin-xiu; LI Xiao-qiang; WANG Guo-dong; LIU Xiang-hua

Materials and Mechanical Engineering > 2006 > 30(11): 43-44.

YI Hai-long, DU Lin-xiu, LI Xiao-qiang, WANG Guo-dong, LIU Xiang-hua. A New 700 MPa Low Carbon High Strength Steel[J]. Materials and Mechanical Engineering, 2006, 30(11): 43-44.

Citation:

YI Hai-long, DU Lin-xiu, LI Xiao-qiang, WANG Guo-dong, LIU Xiang-hua. A New 700 MPa Low Carbon High Strength Steel[J]. Materials and Mechanical Engineering, 2006, 30(11): 43-44.

Citation:

YI Hai-long, DU Lin-xiu, LI Xiao-qiang, WANG Guo-dong, LIU Xiang-hua. A New 700 MPa Low Carbon High Strength Steel[J]. Materials and Mechanical Engineering, 2006, 30(11): 43-44.

PDF (814 KB)

A New 700 MPa Low Carbon High Strength Steel

More Information

Received Date: January 13, 2006

Graphical Abstract

Abstract

Abstract

A low carbon high strength steel with lower yield strength reached 700 MPa was developed through controlling rolling and controlling cooling,and its microstructures and strengthening mechanisms were analyzed.The results show the microstructure of this steel is ferrite and the high yield strength of steel is caused by fine grain ferrite and fine microalloy carbonitrides particles precipitated in ferrite.The amount of precipitation-strengthening is 250 MPa,this is the two or four times higher than that of hot-rolled microalloyed steels in the past.Good elongation is duo to high dislocation density and fine distribution of carbide particles.
- controlling rolling,
- controlling cooling,
- low carbon high strength steel

FullText(HTML)

References (11)

References

[1]	Misra R D K,Nathani H,Hartmann J E,et al.Microstructural evolution in a new 770 MPa hot rolled Nb-Ti microalloyed steel[J].Materials Science and Engineering A,2005,394(1-2):339-352.
[2]	Naoki N,Matthias M.Modelling of microstructure evolution during hot rolling of a 780 MPa high strength steel[J].ISIJ International,2005,45(1):82-90.
[3]	Funakawa Y,Shiozaki T,Tomita K,et al.Development of high strength hot-rolled sheet steel consisting of ferrite and nanometer-sized carbides[J].ISIJ International,2004,44(11):1945-1951.
[4]	Pyshmintsev L Y,Mesplont C,Jacobs S,et al.Microstructure and properties of hot-rolled high strength multiphase steels for automotive application[J].Steel Research,2002,73(9):392-402.
[5]	Du Linxiu,Liu Dongsheng,Liu Xianghua,et al.The investigation of deformation behavior of low carbon steel in the temperature range of strain-induced phase transformation[J].Materials for Mechanical Engineering,2000,24(6):8-12.
[6]	Herman J C,Donnay B,Leroy V.Precipitation kinetics of microalloying additions during hot-rolling of HSLA steels[J].ISIJ International,1992,32(6):779-785.
[7]	Mekkawy M F,El-Fawakhry K A,Mishreky M L,et al.Effect of finish-rolling temperature on microstructure and strength of V and Ti-microalloyed steels[J].Scandinavian Journal of Metallurgy,1990,19(5):246-256.
[8]	Morales E V,Gallego J,Kestenbach H J.On coherent carbonitride precipitation in commercial microalloyed steels[J].Philosophical Magazine Letters,2003,83(2):79-87.
[9]	Yoshimasa F,Tsuyoshi S,Kunikazu T,et al.Development of high strength hot-rolled sheet steel consisting of ferrite and nanometer-sized carbides[J].ISIJ International,2004,44(11):1945-1951.
[10]	Hodgson P D,Kelly G L,Barnett M R.Recent trends in the thermomechanical processing of steel[J].Materials Forum,2000,24:37-48.
[11]	Sun J L,Kang Y L,Wei X Y,et al.Analysis on the process and mechanical of 800 MPa grade low-alloyed plate[R].Workshop on New Generation Steel.Beijing:Chinese Society for Metals,2001.

Cited By

Get Citation

PDF

XML

Article views PDF downloads

Turn off MathJax

Article Contents

Abstract

References

A New 700 MPa Low Carbon High Strength Steel

Abstract

References

Catalog

Export File

Citation

Format

Content